#Slip on tub spout how to

You’ll need to use steady pressure while turning to encourage movement. Use the pliers or pipe wrench over top of the towel to carefully twist the spout. Thoroughly coat the interior of the faucet, then give it about ten minutes. Use the extension straw that comes on the can of WD-40 and place it into the fixture of the tub. You can also try using WD-40 to remove stubborn screw-in tub spouts. Be careful while removing the tub spout off the copper piping and ensure you don’t loosen any pipe connections in the wall. With spouts connected by copper threaded fitting, you’ll need to exercise caution. Using the pipe wrench or pliers, carefully twist the spout clockwise to release it. This will help protect the tap during removal. To do so, wrap the clean towel around the fixture. Once you have loosened any caulk or copper threaded wiring, you can remove the spout. If there is copper threaded wiring, you’ll need to snip them before removal. If there is caulk around the base of the spout, carefully scrape away the excess before attempting to twist the tap. Remember to turn off the water supply before removing the tub spout.īefore you try to remove the faucet, check for caulk or copper threaded fitting. If your twist-off tub spout is stuck, then you’ll need a clean towel and a pipe wrench or pliers.

#Slip on tub spout how to

How To Remove A Tub Spout Without A Set Screwįaucets that don’t have a retaining screw will need to be removed differently. Ensure that you complete the process gently and carefully so you don’t damage the fixture or plumbing behind it. Use the previous techniques of twisting with constant pressure to remove the tub spout. After you have heated the tap, let the temperature drop slightly until it is safe to work with. The heat may cause the faucet to expand as it increases in temperature. Be very cautious while working with electricity. You are going to need your heat-safe gloves as the faucet may burn you. Although this method is a little bit unusual, sometimes it will do the trick. Use your regular hair dryer to heat the faucet. Now, if your attempts have not proved fruitful and the spout still stubbornly remains stuck, there is another method you can try. Use enough force to remove the tap, but ensure that you don’t use too much power that you leave permanent damage on the surface. If the faucet doesn’t want to cooperate and won’t come loose, twist the tap sideways. Continue until the faucet begins to loosen. Use the Allen wrench to remove the set screw. Since you turned off the water supply and the towel is in place over the drain, it is time to remove the spout. Now that you’re done with that, you can get started on removing the stubborn tub spout. This will prevent unpleasant odors from permeating the air and help you refrain from losing parts down the drain. Once there is no longer water coming from the spout, you’ll need a few towels. There may be some water that will drip out of the spout, but there shouldn’t be much. You may need to turn off your home’s main water supply, so make sure everyone in the household knows before you turn it off to avoid surprising anyone.Ĭheck that you have turned off the water flow to the tub you are working on by turning on the water. Do this by turning off the water supply valve. In that case, jump to the heading labeled, “How To Remove A Tub Spout Without A Set Screw.” Turn Off The Water Supplyīefore you continue, you need to do a few things to prevent a mess. If it doesn’t have a set screw, you likely have a screw-in faucet. If you are working with a slip-on tap, locate the set screw. In that case, it’s time for some troubleshooting. It is probably safe to assume that you have already attempted to remove the tub spout if you are reading this, only to find out that the fixture won’t unscrew and refuses to budge. However, tub spouts tend to be difficult to remove, especially old and corroded models.

If your bathtub is leaking, it may be time to replace the tub spout. The washers in the tap may lose their flexibility over time, resulting in a leaking spout. Faucets that have been around for longer than sixteen years may start to wear out. When To Replace A Tub SpoutĪs with most things, tub spouts begin to wear out after years of usage. They simply twist on and off of the attachment, known as the nipple or the pipe. On the other hand, screw-in (threaded) tub spouts do not have set screws. Slip-on tub spouts fit onto a ½ inch copper pipe. Slip-on faucets have a set screw near the bottom of the tub spout. There are two main types: slip-on spouts and screw-on spouts. To start, you need to figure out what kind of tub spout you have.

How To Remove A Tub Spout Without A Set Screw.